I built this for my Den. I love the design, but would recommend longer 12" pieces if you are going to use the stand outside. We just used it and it blew over at 8". We cut the outside ends at a 45 degree angle to increast the effective length of the base without buying more material.
It also makes it look a bit "cooler" :. Woodworking guide offers anyone of any skill level the ability to build amazing projects. The guide is extra helpful because it offers more detailed explanations, videos and blueprints then your typical woodworker magazine.
Thanks for this post. I was going to make this for my tiger group, but then realized that ALL our dens need one, and this would be a great project for my tigers AND lions to help with. They will love painting them and giving them as gifts to the "big kids. Post a Comment. Thursday, March 15, How to build a Cub Scout flag stand. This is a simple, yet very rugged, design that young boys can carry around. We use them for opening and closing ceremonies at den meetings.
I send the den flag and its stand home with the boys between meetings to build a little den spirit. Ideally you might build one of these for every den in the pack and encourage dens to display their flag during den and pack activities. Using 2 deck screws per 2x4, screw them together leaving just enough room to tighly fit the PVC pipe into the square opening in the middle.
It is key that you secure the base together making a flat bottom. Your lumber might be warped a little you you have to play with it a little to make the base level. Note that the bottom string is tied around the pole with no hole.All items can be bought at a major Home Improvement Store. Attach Swivel Pulley to top Galvanized Pole using a pipe clamp. Simply drop the Mini Solar Crackle Sphere stake into the top end of the pipe.
This light is solar, turns on at night and changes colors. Slide bottom pole into top pole. Using post hole diggers, bury flag pole about 3 feet in the ground. Raise your Flag. Tie rope off on rope cleat. Pray for wind. Question 1 year ago on Step 4. Question 2 years ago on Step 2. I built the flagpole with a few very minor mods for convenience and to accommodate local soil conditions.
My flag has been flying proudly on it for about six months. Do you think the pole could handle that? I have an aluminum pole mast that hung at an angle. It was always getting tangled by the prevailing winds at our house. So the answer was a vertical flagpole. I have long wanted one. In my front yard there are brick planters. In a corner area I drove the PVC pipe down until it hit something hard. Rock, bedrock, or??? I only used one 10' 6" pipe, and my aluminum mast about 5' fit the swedged end of the rail pipe.
And I used some Locktite brand Gel super glue to make sure the fixture head stayed on and was glued to the PVC as well. The solar light is a fantastic idea, and I can't wait for dark to bring it on. I followed the rope instructions, but hung my pulley from a closed up "S" hook at the top of the pole. I got all my needs at my local Lowe's, but harness snaps are available at feed stores as well.
I just like these type of snaps and have one on my dogs leash, too. Just a thought because I'm thinking about building this What if you made the pole a little more solid. You could then fill the remaining space around the wood with adhesive.Whether you're building a flag pole stand for a special holiday or a scouting project, a flag pole stand provides proper display support.
The stand keeps the flag from coming into contact with the ground or blowing over in the wind. The size of stand you build depends on the pole diameter, flag height and flag weight. Paint the flag pole stand to coordinate with the celebration's decor.
Center it in the can. Use a tape measure to ensure it has an equal distance from all sides of the can. Dump 4 inches of premixed concrete into the bottom of a 5-gallon bucket. Add water and mix the two until the consistency is like chunky peanut butter.
Use a stick to do the mixing. Hold the PVC pipe in place and pour the concrete around it until it reaches the top lip of the coffee can. Settle the concrete by poking it with the mixing stick. This will help smooth out its surface. Cody Sorensen. Cody Sorensen has been writing professionally since His online articles focus on his experience with painting, horticulture, construction, plumbing, home improvement and agriculture.
Sorensen is a licensed truck driver, certified forklift operator and a journeyman painter. He studied organizational communications at Brigham Young University. Flag stands support flag poles so you don't have to. Step 1. Set a 1-gallon coffee can on the ground. Step 2. Step 3. Step 4. Step 5. Allow the stand to dry 48 hours before using. Warning Avoid touching the concrete; the lime in it can irritate skin. Show Comments.Never install a metal flag pole near power lines or in an area where it may be struck by vehicles.
Severe injury or fatality may result if adequate clearance isn't provided. Galvanized pipe is well-suited to such an application due to its resistance to the formation of rust, which could weaken the metal.
Due to this resistance to rust, such pipe can be used as a permanent mast for flying a flag, where untreated steel pipe must be removed periodically and replaced with new pipe to replace a rusty, corroded section. Lay the galvanized pipe on the ground.
How to Make a Flag Pole Stand
Measure 1 foot from one end of the pipe the top and mark where the hole is to be drilled to secure the top bolt-on pulley assembly. In like manner, measure 5 feet from the other end and mark where the hole is to be drilled to secure the bottom bolt-on pulley assembly. Make sure the bolt-hole markings on the top and the bottom are lined up as perfectly as possible.
Select a suitable drill bit for the size of bolts which came with the pulley assemblies and drill the top and bottom holes in the pipe. Drill through one side of the pipe wall and continue drilling until the bit exits through the outside of the other wall of the pipe.
Bolt the pulleys onto the pipe with an appropriate wrench set, placing a lock washer and nut on each. Tighten until hand-tight, then tighten further until the nuts cannot be turned any more. Use caution so the bolts aren't stripped while tightening. Thread rope through the pulleys and tie a knot in the rope just above the lower pulley. Connect a flag clip to the rope at this knot, then measure the correct distance to the position of the other flag clip hole on the flag and install another into position on the rope measure the distance of the holes in the flag itself for accurate positioning of the clips for your particular flag.
Dig a square hole where the mast is to be set, 4 feet deep and 2 feet wide. Set 4 feet of the 5-foot end into the hole and have a partner assist by holding the pipe in place, as straight as possible. Drive four 4-foot sections of copper grounding rod into the ground about 1 foot out from each corner of the square hole, driving them at a degree angle so the rods are aiming away from the pipe.
Tie pieces of rope to each of the rods and also to the galvanized pipe so the ropes are holding the pipe vertically into place. This will prevent the pipe from leaning while the concrete slab dries after pouring. Check the pipe with a carpenter's level by pressing the edge against the side of the pipe on all sides. Adjust the pipe until the bubble in the level is between the center marks on the observation glass cylinder, then tighten the ropes to hold the pipe to prevent movement.
Fill the hole with concrete until level with the ground. Smooth the top and allow to cure for several days to a week before removing the securing ropes and rods. He attended Western Nebraska Community College. Hunker may earn compensation through affiliate links in this story. Things You'll Need Galvanized pipe, at least 18 feet in length 2 bolt-on pulleys with bolts Drill with drill bit set Open-end wrench set Rope diameter to fit pulley grooves Flag clips Shovel Concrete, enough to fill a square hole 4 feet deep and 2 feet wide Carpenter's level 4 pieces of copper grounding rod, 3 to 4 feet long Sledge hammer.Pro flagpole installer Tony Clayton recommends planting the pole as Allen did: by sinking 10 percent of the pole's height into a PVC sleeve.
A 6-inch crushed-stone setting bed and an pound bag of ready-to-mix concrete hold the sleeve in place. Set the pipe on gravel, add half the mixed concrete, and plumb the sleeve with a 4-foot level, reading the level flush against two points in the sleeve. Add the rest of the mix, check plumb while tamping the concrete, and wait 48 hours. The sleeve forms a tight fit, so Allen lubes the pole with Vaseline for easy removal in a storm. Steel poles, and any over 25 feet, are overkill.
Sectional poles work--they're easier to move but weaker than single-piece models. Tuck the last 6 inches of rope into the knot. Don't pull the rope too taut--it shrinks and tightens.
Join rope ends in a sheet bend between the flag clips to stop the rope knot from snagging in the pulley. The slack should dangle just above the ground. Site the pole with power lines and branches at least 5 feet from the extended flag's edge. Type keyword s to search. Today's Top Stories.
Can Sugar Destroy a Car's Engine? White Claws Are Fine. These Highballs Are Better. This Warship Is On Fire. It May Never Be Saved. Click to Enlarge. This content is created and maintained by a third party, and imported onto this page to help users provide their email addresses. You may be able to find more information about this and similar content at piano.
This commenting section is created and maintained by a third party, and imported onto this page.Many people display flags, such as Boy Scouts and patriotic individuals.
Flags are also proudly displayed on municipal buildings.
There are many different methods of displaying flags. One of the more popular ways, particularly among Boy Scouts, is to build your own flag stand out of wood. In fact, many Cub and Boy Scout troops require that their new members make flag stands. Measure your 1-by-6 board with your tape measure. Cut the boards along your marks with your chop saw or hand saw. Set the board aside to dry. These stacked boards will serve as foots for the flag stand. Place clamps on each of your stacks and allow the glue to dry.
Glue the stacked wood onto either end of one of the inch-long boards. Place the clamps on these boards and allow them to dry. Glue the remaining five inch-long boards onto either end of the other inch-long board. Clamp these glued pieces and allow them to dry. Place the board with the four pieces on the ground and with the board with the "longer" feet on top.
Place the boards at degree angles so they form an "X. If you have formed one, none of the ends of the X will be any longer than any other end. Draw your measurements on your plywood with a carpenter's square and a pencil. Cut out the squares with your circular saw or hand saw. Draw a line with your pencil from corner to corner on each of the pieces of plywood that you just cut to determine the exact center of each piece.
Drill through each of these boards using your drill press and Forstner bit. Take great care during this step to ensure that you are making your hole in the exact center of each of your boards. Stack the same-sized boards on top of one another and glue them together.
Glue the three sizes together in increasing size order. This will make a pyramid-shaped structure when you are done. Glue this pyramid into place on your stand. You can use nails to hold the pyramid in place when the glue dries. Make sure that you drill your holes in the exact center of the boards you are going to use for your flag base. If your holes are drilled off center, the flag pole will not slide down into the base.
Crafts Woodworking Woodworking Projects. Jay Angel. Jay Angel has been a writer sincespecializing in scientific writing, as well as articles about fishing and hunting. Build your own flag stand. Step 1. Step 2. Step 3.
How to Build Your Own Flagpole With Galvanized Pipe
Step 4. Step 5.Give your tailgating camp a true mark of distinction—and make sure your friends can find you as they file into the party—with this do-it-yourself PVC flag pole and custom flag. We made a stencil with our very own logo using a simple computer printout. You can get crafty customizing your own tailgating logo—so let your imagination be your guide.
Your local Home Depot store can help you make these cuts. Just ask an associate. Print a logo or slogan out on regular printer paper. We used a collegiate looking A for Apron, of course. Enlarge the logo to the correct size for your flag. Cut out the interior of your design. A simple design usually turns out better. Tape your flag to the posterboard stencil to keep it in place.
Flip the design over and spray paint the flag using your handmade stencil. You may have to hold down the stencil to keep the design crisp but a little spray around the edges gives it the feel of a stamp, which we think looks cool. Assemble the base, using this picture as your guide. Measure your final, dried flag against the 2-foot piece of PVC pipe. Centered on the 2-foot piece of PVC is usually best. Place the screw hooks through the PVC pipe at the holes.
Make a small incision in the flag for the anchor hooks. Loop the anchor hook through the screw hook then attach it to the flag. Attach the 2-foot piece with the flag on it to the 4-foot piece, either with a degree coupler or a degree coupler, as is shown.
Attach that to the foot piece with the coupler or use a shorter piece if desired. Optional: Fill the bottom of the base with sand to make the structure more secure in a windy location. Or just fill some bags with sand and sit them on the base when needed.
And now that you have your PVC flag pole and homemade flag, head to The Home Depot for everything you need for tailgating. It also helps fans find great tailgating products at great prices. Tell us a little bit about you and we'll find articles to fit your tastes. To start, just select some of the options below.DIY Festivus Pole and Stand Quick Easy Limited Tools Seinfeld Inspired Project
The Home Depot Blog. Style Challenges. Room Ideas. Connect With Us. Share article with:. Print Email. One 8- to foot piece or any custom height you would like for your flagpole One 4-foot piece Six 6-inch pieces Two inch pieces Make the flag Print a logo or slogan out on regular printer paper.
Trace the design on posterboard then cut out the interior again so you have a stencil. Make the PVC flag pole Assemble the base, using this picture as your guide.